Shopping Cart
IoT
Last items in stock
US$2.43
This is a perfect connector pack for various DIY projects with the ODROID-C0. You need a soldering skill to use this pack.
US$8.95
Raspberry pi best value power supply which will give you actual 5V after complete boot up. Ideal for general purpose as well, like any device with micro-USB
Last items in stock
US$1.75
5pieces of 10pin male header is excellent choice for your DIY project.
US$8.95
100% full load burn-in testPass LPSProtections: Short circuit / Overload / Over voltage / Over temperatureClass II power (without earth pin)2 pole USA plug
In Stock, Shipping Now
US$12.95
WIFI Module #5BK uses the same chipset (Realtek RTL8821CU) as WIFI Module #5B, so it is 100% compatible. IEEE 802.11ac/a/b/g/n WLAN and Bluetooth combo module with onboard 2.4Ghz and 5.8Ghz Dual band antenna.
Out of Stock, Order to Reserve
US$91.00
The ODROID-M1 is a single board computer with a wide range of useful peripherals developed for use in a variety of embedded system applications.
Last items in stock
US$22.00
Flirc allows you to pair any remote control with your computer or media center (Including the Raspberry Pi!). Just walk through our super simple cross platform pairing application, and you're done. Use your previously paired remote with no additional software on any machine with Flirc. It's basically a universal IR receiver, so can be used with any remote...
Last items in stock
US$6.80
The official external antenna for your Compute Module 4. Certified for use with Raspberry Pi Compute Module 4.
Note: CM4 and IO board not included
Last items in stock
US$14.50
A new and upgraded version of the USB-UART Module Kit featuring a USB-C Port.
Out of Stock, Order to Reserve,
US$7.55
A super handy switch cable for your Raspberry Pi 4 Model B , removing the need to pull the USB-C connector out of your Raspberry Pi (or mess around with sockets/plugs) every time you want to power up/down.
US$10.95
This is a breadboard, good for small projects. It's 5.5 cm x 16.5 cm with a standard double-strip in the middle and two power rails on both sides.
US$5.25
40 Pcs of Dupont wire with 20CM length, ideal to connect for your Raspberry Pi project.
Last items in stock
US$15.00
The UPS(Uninterrupted Power Supply) Kit is designed specifically for the ODROID-M1S.It is equipped with a 18650 rechargeable Li-Ion battery holder, charger control IC and a 5Volt Boost DCDC.There is a small MCU on the board which measures the battery level and communicate with the ODROID-M1S board via USB interface.
Last items in stock
US$2.35
GPIO Header for Raspberry Pi - Extra tall 2x13 Female Header
Last items in stock
US$2.99
A new add-on board that utilizes the USB signal lines of the ODROID-M1S 14-pin expansion header connector. Your M1S is now connected wirelessly with the built-in WiFi module inside the case. It also provides a solution to the limited number of USB ports on the M1S. Other small USB adapters like a wireless keyboard/mouse USB dongle can be embedded into the...
Last items in stock
US$32.95
The board itself is tiny, at around 25mm x 20mm x 9mm. It also weighs just over 3g, making it perfect for mobile or other applications where size and weight are important
US$5.95
The USB 2.0 Extension Cable extend the distance between your USB peripheral and your USB hub or computer assure good signal quality to meet USB specification.
In Stock, Shipping Now
US$10.95
Separated pin plugs, this cable is ideal for powering and connecting up to the debug/login console on the Raspberry Pi or BeagleBone Black. Connect the pins as shown to power the Pi or BBB and establish the RX/TX link.
US$4.25
The connector heads measure 0.51" x 0.36" x 0.25" (13.0 x 9.3 x 6.3 mm) on the USB micro B end and 0.51" x 0.55" x 0.25" (13.0 x 13.8 x 6.3 mm) on the USB A end.
US$6.95
Raspberry Pi® computer you just got has a row of 2x13 pin headers soldered on - those are the GPIO (general purpose input/output) pins and for those of us who like to hack electronics they are where the real fun is. By programming the Pi, you can twiddle those pins high or low, send and receive I2C and SPI data, and access the 3V and 5V power rails.
Last items in stock
US$6.95
Make your Pi a little slimmer with this microSD card adapter board. It slides in where the SD card goes but is half the length. Pop in a microSD card for a sleeker machine. The microSD card holder is a push-push type so you can push on the edge that sticks out to remove the card when necessary.