The HiFi Shield Plus provides both stereo RCA connectors to connect to external amplifiers and other audio equipment. Via TI’s high-end PCM5242 DAC chip(known as Burr-Brown), it supports 16, 24, 32 bit audio formats with minimal THD+N ratio (0.002%) and ideal dynamics (114dB+), plus amazing sampling rates of 384kHz
U3 IO Shield is the board that can be plugged on the neat of ODROID-U3 via tiny 8 pin IO connector. You can have 36 IO ports of GPIO/PWM/ADC. The shape and dimension are exactly same as ODROID-U3. It comes with 12pcs of PCB spacers for easier and solid stacking assembly.
Best low-cost environmental sensing solution with BME280 and Si1132 on one board. The combination of the BME280 sensor and the Si1132 sensor enables measuring temperature, barometric pressure and humidity, UV Index and ambient light at once. 6pin header socket is already soldered. You can simply plug it on to the right connector.
This MIPI camera kit has an OV5647 sensor chip which can capture up to 5 Mpixel images and 720p/30fps video streaming. You can get reasonably good imaging whether it is in the daytime or at night thanks to the automatically switchable IR-Cut filter and two IR Lights. Realtime image inputs from the MIPI-CSI port can be widely used for Machine-Learning...
The Stepper Motor Controller Board is mainly designed to control up to 6 stepper motors and can help to interface with peripherals through CAN bus and several GPIO pins. Most adaptable application with this board is 3D printer or CNC machine that usually uses 3~4 stepper motors. Different type of machines require different hardware functions, unsupported...
The UPS2 for C1 is designed specifically for the ODROID-C1. Uninterrupted Power Supply is an electrical apparatus that provides emergency power to a load when the input power source, typically mains power, fails. The on-battery runtime of most uninterruptible power sources is relatively short but sufficient to start a standby power source or properly shut...
Uninterrupted Power Supply is an electrical apparatus that provides emergency power to a load when the input power source, typically mains power, fails. The on-battery runtime of most uninterruptible power sources is relatively short but sufficient to start a standby power source or properly shut down the ODROID.
RTC backup battery Lithium primary battery to back up the RTC on XU board. This battery can keep the RTC running up to 5 years without external power supply.
The ROM-WT138LM(N) series are remote control receiver modules. Pin diode and receiver IC are assembled on one module. Small- sized, light-weight, and low current consumption. modules have been achieved by using resin mold.
The HC-SR501 Infrared PIR Motion Sensor Module auto-senses light in various applications (in house, basement, outdoor, warehouse, garage, etc,) for ventilator control, alarm, etc. Infrared technology (LHI778 probe design) high sensitivity & high reliability. ultra-low-voltage. widely used especially for battery-powered products. This HC-SR501 Infrared...
This RGB color sensor module is based on the TCS34725 sensor chip made by TAOS. The module is designed by Adafruit who Called it (the best color sensor in the market). This is much confirmed by our own testing and experiments in future Electronics Egypt lab.
This module is the 16 way GPIO expander for the I2C interface, and built with the MCP23017.MCP23017 has a high-speed I2C interface which supports the I2C frequency of 100KHz, 400KHz and 1.7MHz. The chip has 3 address pins, which can be set up for 8 different addresses. So 8 modules can be connected through two I2C buses to achieve up to 128 IO extensions.
A single native (non-USB) SATA 3.0 port on the ODROID-M1 is provided for use with a 2.5inch HDD or SSD NAND Memory storage device. This SATA interface delivers near 500MB/s of sequential access. The SATA mount kit contains a SATA Data cable, a SATA Power cable, and a mount plate with some support screws. However, since the SATA power port doesn’t have a...
SATA cables are perfect for system builds with tight fitting environments with ODROID-H2 Case Type 1, Type 3 and Type 4 to connect a SATA HDD/SSD storage. Utilising compact stackable connectors, this flexible 200mm cables are neat and manageable.
Replacement speaker and joystick assembly for the ODROID-Go Advance system. A direct replacement part for the ones included in the original build of the ODROID Go Advance as shipped.
WIFI Module #5BK uses the same chipset (Realtek RTL8821CU) as WIFI Module #5B, so it is 100% compatible. IEEE 802.11ac/a/b/g/n WLAN and Bluetooth combo module with onboard 2.4Ghz and 5.8Ghz Dual band antenna.
The UPS(Uninterrupted Power Supply) Kit is designed specifically for the ODROID-M1S.It is equipped with a 18650 rechargeable Li-Ion battery holder, charger control IC and a 5Volt Boost DCDC.There is a small MCU on the board which measures the battery level and communicate with the ODROID-M1S board via USB interface.
Showing 101-150 of 152 item(s)
By using this site, you agree to cookies for a better experience. See Privacy Policy.
