This industrial USB to TTL converter adopts an original FT232RL chip, providing greater stability and compatibility, enabling industrial-grade high-performance communication between a computer and TTL devices.
Every single IoT project includes different types of inputs and outputs, physically. With infinite numbers of possibilities, developers need their own custom machined enclosures. That enclosure brings flexibility to add/remove cable interfaces to your project in seconds. IP54 rated lid and grommets enable your project’s environmental robustness. Projects...
The IP based Power Switch is a simple product that automatically power-cycles any device when internet connectivity is lost or you want to do it manually. This is one of the best power solution for remote locations where you have to send tech only for power cycle.
Raspberry pi best value power supply which will give you actual 5V after complete boot up. Ideal for general purpose as well, like any device with micro-USB
The IP based Power Switch is a simple product that automatically power-cycles any device when internet connectivity is lost or you want to do it manually. This is one of the best power solution for remote locations where you have to send tech only for power cycle.
Simplify your Internet of Things with a passive PoE injector cable. These are quite handy for projects that have Ethernet connectivity and also need a power cable.
Enjoy the power of Sophos UTM Home Software ready FW3160 ultra compact x64 networking system built with Intel® Celeron J3160 processor with Intel® AES New Instructions capable.
Supports SATA Interface rate of 6Gb/s. Ultra high-performance and low power consumption, Supports dynamic power management and SMART TRIM Command Supported
100% full load burn-in testPass LPSProtections: Short circuit / Overload / Over voltage / Over temperatureClass II power (without earth pin)2 pole USA plug
It is a good plastic box for Raspberry Pi, which can protect it with one of these snazzy plastic enclosures?. These cases protect the Raspberry Pi from things like rogue wires that might short it out while still allowing full access to the board! Simply snap the RPi into the bottom half of the enclosure, then snap the two sides together.
Supports SATA Interface rate of 6Gb/s, Ultra high-performance and low power consumption, Supports dynamic power management and SMART, TRIM Command Supported.
A MicroSD card for OS image is a small memory card that's preloaded with an operating system image, such as Linux or Android. It's commonly used to boot up single-board computers and other embedded systems, enabling quick and easy deployment of the operating system. Available in various storage capacities to suit different needs.
It is a good plastic box for Raspberry Pi, which can protect it with one of these snazzy plastic enclosures?. These cases protect the Raspberry Pi from things like rogue wires that might short it out while still allowing full access to the board! Simply snap the RPi into the bottom half of the enclosure, then snap the two sides together. It has windows on...
The USB 2.0 Extension Cable extend the distance between your USB peripheral and your USB hub or computer assure good signal quality to meet USB specification.
Enjoy the power of pfSense® ready FW3160 ultra compact x64 networking system built with Intel® Celeron J3160 processor with Intel® AES New Instructions capable.
Supports SATA Interface rate of 6Gb/s, Ultra high-performance and low power consumption, Supports dynamic power management and SMART, TRIM Command Supported.
It is a good plastic box for Raspberry Pi, which can protect it with one of these snazzy plastic enclosures?. These cases protect the Raspberry Pi from things like rogue wires that might short it out while still allowing full access to the board! Simply snap the RPi into the bottom half of the enclosure, then snap the two sides together.
Cable is made of 24AWG pure copper listed pair conduits with 50u" gold plated contacts (short body). Most budget cables skimp with 10u". 350 MHz Category 5E Patch Cord (UTP)
pfSense® software is a FreeBSD-based firewall tailored for use as a firewall and router. It includes almost all the features of expensive commercial firewalls, and more in many cases.
PCEngines is End of Life, Consider Boingfire Systems.
Cable is made of 24AWG pure copper listed pair conduits with 50u" gold plated contacts (short body). Most budget cables skimp with 10u". 350 MHz Category 5E Patch Cord (UTP)
pfSense® software is a FreeBSD-based firewall tailored for use as a firewall and router. It includes almost all the features of expensive commercial firewalls, and more in many cases.
Enclosure designed for Raspberry-PI boards in rectangular version and consists of two identical halves that fit togather. It has windows on four sides for direct access to components. Well suited for users who frequently connect and disconnect from the PCB ports.
It is card reader and writer, you can fastly transfer your data from your card to your PC, or from your PC to your card. just plug and play! No external power required and NO need to install drivers. Suitable to transfer Images on CF Cards for ALIX /APU boards or others.
Cable is made of 24AWG pure copper listed pair conduits with 50u" gold plated contacts (short body). Most budget cables skimp with 10u". 350 MHz Category 5E Patch Cord (UTP)
Cable is made of 24AWG pure copper listed pair conduits with 50u" gold plated contacts (short body). Most budget cables skimp with 10u". 350 MHz Category 5E Patch Cord (UTP)
pfSense® software is a FreeBSD-based firewall tailored for use as a firewall and router. It includes almost all the features of expensive commercial firewalls, and more in many cases.
Cable is made of 24AWG pure copper listed pair conduits with 50u" gold plated contacts (short body). Most budget cables skimp with 10u". 350 MHz Category 5E Patch Cord (UTP)
Enjoy the power of OPNSense® Software ready FW3160 ultra compact x64 networking system built with Intel® Celeron J3160 processor with Intel® AES New Instructions capable.
Now Comes with Sensei pre- installed.
Use Spade Wire fork terminal with 19" DualBoard Enclosure System for ALIX/APU Boards (CASEDUALBOARD2) and AC to DC Internal Power Supply 35W (RS-35-12).
IP68 Rated Outdoor Weatherproof field replaceable RJ45 Ethernet connector system. 15CM shielded Cat5e cable.Cat5e RJ45 Plug 8P8C. The system features a shielded RJ45
This M.2 to PCIe Adapter – Straight is your solution for seamless expansion, uncompromising reliability, and versatile compatibility. Enhance your system’s capabilities today!
Do you want your Raspberry Pi with a more modern and stylish design? Here comes Argon ONE. An aluminum case for your Raspberry Pi board to give it a more decent look.
Designed to keep your Raspberry Pi 4 Model B cool, our case features 'hex' ventilation paired with a 5V cooling fan (included). Also includes a set of rubber feet!
The perfect home for your new Raspberry Pi 4. We will ensure our case is adjusted to fit the latest Raspberry Pi specifications.
Note "Only tested for the Raspberry Pi 4B"
Does not support Pi 3B+, 3B, or 2
This robust metal enclosure has been designed specifically for the official Raspberry Pi Compute Module 4 IO board and comes complete with fixings, a cooling fan and a bonus included screwdriver.
The official Raspberry Pi 4 Model B case, available in a stunning black & grey design. No fixings or tools are required - your Raspberry Pi 4 simply clips into the lower section of the case and the lid pops on too!
Exact specifications as per PCEngine's recommendations. Suitable for all ALIX boards other than ALIX.1D/1E, Switching adapter with US plug, with FCC. ROHS and CEC compliant.
The Raspberry Pi Case is designed to be fully customisable by the user, and adaptable to suit a range of requirements. The streamlined look and adaptability make it perfect for many applications.
Exact specifications as per PCEngine's recommendations. Suitable for all ALIX boards other than ALIX.1D/1E, Switching adapter with US plug, with FCC. ROHS and CEC compliant
This is an armor aluminum alloy case designed for the Raspberry Pi 4 computer model b. It is a great passive cooling case to help raspberry pi 4 board cooling down.
Note: the raspberry pi 4 board is not inlcuded in the packing list.
Exact specifications as per PCEngine's recommendations. Suitable for all ALIX boards other than ALIX.1D/1E, Switching adapter with US plug, with FCC. ROHS and CEC compliant
Designed for Raspberry Pi 4 Model B, these cases are durable and strong.Besides, the product offers a high heat conductivity and excellent corrosion resistance, which is able to better protect your Pi board.The anodizing process performed on the surface of the metal greatly improves the quality of the case visually and tactually.All ports and slots of the...
Compact size AC adapter, saves space on power strips. Input voltage 100-240 V AC, 47-63 Hz. Output voltage 12 V DC, maximum current 2.0A. High efficiency. 2.5 mm jack, center positive.
Compact size AC adapter, saves space on power strips. Input voltage 100-240 V AC, 47-63 Hz. Output voltage 12 V DC, maximum current 2.0A. High efficiency. 2.5 mm jack, center positive.
These spacers increase the internal height of our Modular Raspberry Pi Case by 10mm per spacer and can be stacked to increase the headroom further. Additional (longer) screws required - please read below notes.
Compact size AC adapter, saves space on power strips. Input voltage 100-240 V AC, 47-63 Hz. Output voltage 12 V DC, maximum current 2.0A. High efficiency. 2.5 mm jack, center positive.
The SIKENAI adapter is a fast charging adapter which is perfect to charge phones. High Voltage charging (5V3A, 9V2A), Efficient Performance and more useful for mobile phones.
Imaging service for SD, Micro-SD, mSATA or SSD Drives. Bulk installation service empowers you to minimize the project time by outsourcing lenghty and tedious work.
This adapter can be used with ALIX.1 boards, which require 12V power. Not recommended for other ALIX boards, which have the 2.1 mm instead of 2.5 mm jack.Compact size AC adapter, saves space on power strips.
Imaging service for SD, Micro-SD, mSATA or SSD Drives. Bulk installation service empowers you to minimize the project time by outsourcing lenghty and tedious work.
This connector is ideal to extend Null Modem Cable with DB9 male connectors, allowing you to connect a serial printer to a 9-pin serial port, or transfer files from PC to PC via serial cable connection.
The RC Air Mouse and Keyboard uses the latest 2.4GHz wireless technology with a sampling frequency up to 120Hz. Use it like a Wii remote to control your mouse cursor on the screen.
MMCX Right Angle to RP-TNC Male Bulkhead. Suitable for indoor/outdoor wireless devices, application of this cable to make connection between mini-pci card to antenna.
High-performance DDR5-5600 SODIMM memory module with 1.1V low power consumption, featuring 46-45-45 timings and unbuffered design. Ideal for laptops and compact systems requiring fast, efficient, and stable memory performance.
The FW3160 is a compact network appliance suitable for firewall, thin client, network appliance, desktop, display client, and CPE applications. It features an Intel Celeron J3160 quad-core processor with Turbo Boost up to 2.24GHz, 8GB max RAM capacity, 1x mSATA storage, 2x HDMI display ports, and Intel AES-NI security acceleration. It supports various...
This is an all-aluminum structured computer hardware with a fanless design, ensuring silent operation. It's powered by an Intel Core 10th Gen i5-10210U processor and is compatible with Windows 11, benefiting from TPM2.0 support. The fanless mini PC offers flexibility in memory and storage with a DDR4 memory slot (supporting up to 32GB) and slots for an...
The FW7100 is a small form factor fanless computer designed for network applications. It features an Intel Core i3-8130U CPU with 2 cores, up to 3.40GHz frequency, and hyper-threading. It supports up to 32GB of DDR4 RAM, mSATA and 2.5" SSD storage, and 6 Ethernet ports with Intel 82583V controller. It is compatible with Windows 10, Linux, pfSense, and...
NCA-1515 is a compact, fanless network appliance designed for use in industrial and embedded computing applications. It is equipped with an Intel Atom C3000 series processor, up to 16 GB of DDR4 memory, and multiple Ethernet ports for high-speed network connectivity. The NCA-1515 also features a rugged design with a wide operating temperature range,...
The FW2700 is a compact and versatile computer system capable and flexible system with a range of features that make it suitable for a variety of applications, including networking, security, and industrial automation.
Good thermal conductivity performance to join CPU/GPU and heat sink together. CPU's heat can be passed to the heat sink faster and also Enhances the cooling effect of heat sink.
5G Development Kit is for M.2 package 5G modems designed to work with the Raspberry Pi. The raspberry Pi 5G modem allows you to develop, trial, and test your ideas on this platform in preparation for the commercialization of 5G devices and networks. Data throughput up to 5.0 Gbps DL and 1.0 Gbps UL is possible with that kit.
3510 Version Extreme Cooling Fan Kit For Raspberry Pi 4B is a brandnew Cooling system for your Raspberry Pi 4B.It's a completely new radiator, and it's a very cool cooling system after the armor shell.The fan is 3510 version and more powerful but still quite when it is running.Two aluminum blocks will touch the MCU tightly and good for the heat...
Are you bothered by the heat problem of the Raspberry Pi? Don't worry, we have prepared a set of heat dissipation solutions for Raspberry Pi 4B. These black aluminum heat sinks of various sizes adopt a slotted design on the surface, which is more conducive to heat dissipation. They also come with adhesive backing for easy installation.
This 19.5cm long SMA antenna has high gain and is perfect for 4G/LTE applications. It covers your long-range needs with 50 ohm impedance and 6dBi gain.
The Rj45 inline coupler from CorpShadow allows you to extend the length of two CAT 5/5e patch cables quickly and easily. Designed to provide a female-to-female connection.
Are you still bothered by the Raspberry Pi fever problem? Don’t worry, we have prepared a cooling solution for the Raspberry Pi 4B.
Aluminum heat sink is adopted due to its highly cooling feature and excellent resistance to oxidation, which can effectively avoid chip over-heating problem.The surface is designed with slotting, which is more conducive to...
DDR4 PC4-19200 SODIMM is a high-performance, low-latency memory module designed for use in modern computing systems, such as laptops, mini PCs, and embedded devices. With a speed of 2400MHz and a capacity of up to 16GB, this memory module is ideal for multitasking, data processing, and running memory-intensive applications. Its low-voltage and...
Flirc allows you to pair any remote control with your computer or media center (Including the Raspberry Pi!). Just walk through our super simple cross platform pairing application, and you're done. Use your previously paired remote with no additional software on any machine with Flirc. It's basically a universal IR receiver, so can be used with any remote...
The connector heads measure 0.51" x 0.36" x 0.25" (13.0 x 9.3 x 6.3 mm) on the USB micro B end and 0.51" x 0.55" x 0.25" (13.0 x 13.8 x 6.3 mm) on the USB A end.
Raspberry Pi® computer you just got has a row of 2x13 pin headers soldered on - those are the GPIO (general purpose input/output) pins and for those of us who like to hack electronics they are where the real fun is. By programming the Pi, you can twiddle those pins high or low, send and receive I2C and SPI data, and access the 3V and 5V power rails.
lets you connect 9-pin (DB9) or 25-pin (DB25) RS232 serial devices to your laptop or desktop computer through a USB port, as though the computer offered an onboard serial port. The integrated 3' (0.9m) cable connects directly from the serial device to the computer without requiring additional cables.
PC Engines SATA data with Power cable for APU Boards has three connectors, , data / power on drive end, separate SATA data and 2 pin power header for APU System board end.
PC Engines SATA data with Power cable for APU Boards has three connectors, , data / power on drive end, separate SATA data and 2 pin power header for APU System board end.
The Raspberry Pi Pico is an entirely new type of microcontroller from Raspberry Pi. Small, cheap and flexible - it’s great for learning to code with MicroPython!
This is a handy interface bridge between Mini PCIe 3G/4G/LTE modules and Raspberry Pi. You can easily insert a Mini PCIe module in this shield then start using high-speed cellular internet with your Raspberry Pi.
You also need to get a EC25 Mini PCle 4G/LTE Module and Antennas to make this product works.
Cable constructed using the high quality material for best contact connection between HDMI equipment.
Fully supports HDMI ethernet channel and HDMI 3D features.
Extend the reach of your USB 3.0 devices with CorpShadow's USB 3.0 compliant usb extension cables. Backward compatible with previous versions of USB but speed tested to be able to support the newest standard as well.
USB 3.0 has arrived with supporting speeds more than 10X that of it's predecessor. Up to 5.0 Gbs. These cables will allow you to connect new USB 3.0 devices to your USB 3.0 enable computer or controller.
