Availability: Out of stock
This is a spare board for ODROID-GO Advance Black Edition. This is NOT compatible with the original ODROID-GO Advance.
ODROID-H2 Case Type 7
Reference: ODH2CASE7A
US$20.80
This “Case Type 7” is designed for the user who needs high bandwidth network with mid-range storages.
- Supported storages:
- On-board eMMC 5.1 module
- On-board M.2 NVMe (NGFF-2280)
- Up to 2 x 2.5” SATA HDD or SSD (Max height : 15mm)
- SATA Data & Power cables must be purchased
- This case is compatible with the H2 Net Card, which is not included in the package.
- The disk drive mounting screws (M3x6mm) are included in the package.
- The power and reset switches are accessible through the hole at the front
- Optional LED Power Button (diameter: 16mm) can be installed at the front
- Size : 128 (L) x 157 (W) x 111 (H) mm
Package contents:
- A. Bottom panel
- B. Front panel
- C. 2.5″ SATA HDD/SSD bracket
- D. 2.5″ SATA HDD/SSD bracket
- E. Left Panel
- F. Right panel
- G. Top panel
- H. Inner bracket
- I. Rear panel
- J. 16 x 6mm M3 Truss Head Bolts
- K. 4 x M5 Nuts
- L. 4 x M5 Truss Head Bolts
- M. 2 x 16x9mm (M) Steel PCB Supports
- N. 4 x 40mm (F) PCB Supports
- O. 4 x 20mm (M) PCB Supports
- P. 4 x 40mm (M) PCB Supports
- Q. 4 x Rubber Feet (Round / Clear)
- R. 1 x 92mm Stainless Cooling Fan Grill
Note* photo includes spare parts image for some supports and screws. Standard part quantity for this product is same as Package contents description above.
Optional accessory
Mechanical drawings
ODH2CASE7A
Data sheet
- Cutouts
- HDMI PORT, DISPLAY PORT, ETHERNET PORT, AUDIO PORT, USB2.0 PORT
- Width
- 157 (mm)
- Height
- 111 (mm)
- Length
- 157 (mm)
- Board Category
- ODROID-H2+
This “Case Type 7” is designed for the user who needs high bandwidth network with mid-range storages.
16 other products in the same category:
Availability: 5 In Stock
PWM port on ODROID-XU4 2pin header which connector is Molex 51021-0200 / 1.25mm pitch.
The fan motor speed is controlled by CPU temperature proportionally
The fan motor speed is controlled by CPU temperature proportionally
Availability: 8 In Stock
Hardkernel recommanded enclosure for Odroid-U3 system board.
Availability: 4 In Stock
The MC1 was originally designed to be 4 stackable units, each with a specially designed Single Board Computer (SBC) based on the Samsung Exynos 5422 Octa-core processor
Availability: 10 In Stock
Availability: 2 In Stock
The ODROID-M1 is a single board computer with a wide range of useful peripherals developed for use in a variety of embedded system applications.
Availability: 1 In Stock
This “Case Type 3” is designed for the user who needs high bandwidth network with mid-range storages.
Availability: 3 In Stock
Use this USB-DC Power Bridge board with ODROID-XU4 to connect ODROID-VU7 or VU7 Plus
Availability: 2 In Stock
Real Time Clock Shield for the ODROID-C2
Availability: 2 In Stock
CM108AH is a highly integrated single chip USB audio solution.
All essential analog modules are embedded in CM108AH, including dual DAC and headphone amplifier, ADC, microphone booster, PLL, regulator, and USB transceiver.
Availability: 2 In Stock
The UPS2 for C1 is designed specifically for the ODROID-C1.
Uninterrupted Power Supply is an electrical apparatus that provides emergency power to a load when the input power source, typically mains power, fails. The on-battery runtime of most uninterruptible power sources is relatively short but sufficient to start a standby power source or properly shut down the ODROID-C1
Availability: 3 In Stock
Highly recommended item to protect a ODROID-HC2.
Availability: 2 In Stock
Fully assembled 3.2inch display with 320x240 pixels TFT LCD and a resistive touch overlay. Just plug it on top of ODROID-C1. 2x13 tall female header is already soldered on the PCB.
Availability: 12 In Stock
This board contains a USB3.0 to SATA3 controller (JMicron JMS578) allowing interfacing of a single 2.5" SATA HDD/SDD
Availability: Out of stock
This “Case Type 2” is designed for the user who needs high performance network with a minimal or regular range storages.