Raspberry pi best value power supply which will give you actual 5V after complete boot up. Ideal for general purpose as well, like any device with micro-USB
The UPS(Uninterrupted Power Supply) Kit is designed specifically for the ODROID-M1S.It is equipped with a 18650 rechargeable Li-Ion battery holder, charger control IC and a 5Volt Boost DCDC.There is a small MCU on the board which measures the battery level and communicate with the ODROID-M1S board via USB interface.
100% full load burn-in testPass LPSProtections: Short circuit / Overload / Over voltage / Over temperatureClass II power (without earth pin)2 pole USA plug
By using this Metal Plate, you can give Khadas box some weight this way issue of low weight device placing fixes. This is optional but good to have, doesn't let move your Khadas box due to cable stretch.
A new add-on board that utilizes the USB signal lines of the ODROID-M1S 14-pin expansion header connector. Your M1S is now connected wirelessly with the built-in WiFi module inside the case. It also provides a solution to the limited number of USB ports on the M1S. Other small USB adapters like a wireless keyboard/mouse USB dongle can be embedded into the...
Flirc allows you to pair any remote control with your computer or media center (Including the Raspberry Pi!). Just walk through our super simple cross platform pairing application, and you're done. Use your previously paired remote with no additional software on any machine with Flirc. It's basically a universal IR receiver, so can be used with any remote...
A super handy switch cable for your Raspberry Pi 4 Model B , removing the need to pull the USB-C connector out of your Raspberry Pi (or mess around with sockets/plugs) every time you want to power up/down.
The RC Air Mouse and Keyboard uses the latest 2.4GHz wireless technology with a sampling frequency up to 120Hz. Use it like a Wii remote to control your mouse cursor on the screen.
The board itself is tiny, at around 25mm x 20mm x 9mm. It also weighs just over 3g, making it perfect for mobile or other applications where size and weight are important
The USB 2.0 Extension Cable extend the distance between your USB peripheral and your USB hub or computer assure good signal quality to meet USB specification.
Separated pin plugs, this cable is ideal for powering and connecting up to the debug/login console on the Raspberry Pi or BeagleBone Black. Connect the pins as shown to power the Pi or BBB and establish the RX/TX link.
The connector heads measure 0.51" x 0.36" x 0.25" (13.0 x 9.3 x 6.3 mm) on the USB micro B end and 0.51" x 0.55" x 0.25" (13.0 x 13.8 x 6.3 mm) on the USB A end.
Raspberry Pi® computer you just got has a row of 2x13 pin headers soldered on - those are the GPIO (general purpose input/output) pins and for those of us who like to hack electronics they are where the real fun is. By programming the Pi, you can twiddle those pins high or low, send and receive I2C and SPI data, and access the 3V and 5V power rails.
Make your Pi a little slimmer with this microSD card adapter board. It slides in where the SD card goes but is half the length. Pop in a microSD card for a sleeker machine. The microSD card holder is a push-push type so you can push on the edge that sticks out to remove the card when necessary.
The 'M2X WWAN Extension Board' is an ultra-thin version of the 'Original M2X Board'.
It has an M.2 slot for adding a 4G/5G LTE module to your VIM4, VIM3/VIM3L. A nano-SIM card slot for 4G/5G SIM cards. Finally, the 'M2X WWAN Extension Board' still maintains the same form factor as all our VIM single board computers.
BT Magic is a high-fidelity Bluetooth audio receiver module exclusively engineered by Khadas for the Tone2 series. Experience consistent and interference-free wireless audio, simply plug the module into Tone2’s USB (I2S) port.
This pi plate is perfect for when you want to build a stand-alone project with its own user interface. The 4 directional buttons plus select button allows basic control without having to attach a bulky computer.
This pi plate is perfect for when you want to build a stand-alone project with its own user interface. The 4 directional buttons plus select button allows basic control without having to attach a bulky computer.
This cable will let you swap out the stock 150mm long flex cable from a Raspberry Pi Camera (either 'classic' or 'NoIR' type) for a different size. Works great, just carefully open the connector on the Pi and slip this one in.
