Connect the high quality 1024 x 600 display to the ODROID-C2 or ODROID-C1+ via an HDMI link board and a micro-USB link board (both included) which handles power and signal. Then connect a DC plug on the C2 / C1+, once you install the latest OS update, and you are ready to play. Connection to the ODROID-XU4, ODROID-N2 or ODROID-C4 is by HDMI and micro USB cables (both included) as shown below. This touchscreen is designed to work with both Android and Linux.

– 7-inch TFT-LCD
– Screen Resolution: 1024 x 600 pixels hardware resolution, configurable by software up to 1920×1080
– 5 finger capacitive touch input (USB ID 16B4:0705)
– Power consumption : 800mA/5Volt
– Power on/off tact switch
– 3.5mm audio jack and differential L/R speaker port to support HDMI audio output (only 48Khz sampling rate is available)
– OSD menu supports with buttons for power management, brightness/contrast/volume adjustment, etc.
– Wide Viewing angle (in degree) : Left 75, Right 75, Up 75, Down 75
– Screen Dimensions : 172.9 x 124.3 x 15 mm including buttons and connectors
– Viewable screen size : 153.6 x 86.64 mm (active area)

 

components VU7A+

 

Package include

A. Fully assembled 7inch display
B. 6 x 3.5mm screws
C. 3 x Hex nuts
D. Micro USB link board
E. HDMI link board
F. Micro-to-TypeA USB Cable (approx. 35cm)
G. Micro-to-Micro USB Cable (approx. 35cm)
H. TypeA-to-TypeA HDMI cable (approx. 35cm)

Assembly Guide

Option 1 : Mount the C2/C1+ board on the LCD unit with 3pcs of 8mm PCB supporters. The HDMI link board and micro-USB link board are used for interface and power supply.

Option 2 : A Micro-to-micro USB cable and flexible flat HDMI cable can be used as well. The 35cm cable kit is included.

with ODROID-XU4 / ODROID-N2 / ODROID-C4

 

 

Board Detail

+ HDMI A port
+ Power on/ff button
+ 3.5mm audio out jack
+ Differential L/R speaker port
+ 4 x menu buttons
+ MicroUSB port: “Touch” – First attach your board (C2, C1+ or XU4) to the VU7A with an HDMI cable. Then attach the micro USB port next to the HDMI port labeled “Touch” to provide touchscreen power to the VU7A!
+ MicroUSB port type DC: “DC” – Using your speakers or any extra power consuming devices attached to your board, you may need additional power for stable performance. This micro USB port labeled “DC” is to provide extra power when you need it. Use any standard micro usb charger, like the ones used for most Android phones.

 

 

 

The Chromium browser supports the multi-touch pinch- zoom gesture, so you can enjoy the zoom in and out like a smartphone. The touchscreen also works with Android OS for the C1+.

 

Touch the sound!!

vu7ap-descriptional image

 

Known issues.
1. The display shows noise on the screen in the boot process and power-down process because there is no off-sync filter circuit.
2. On the C1+, there will be after-image or noise when the system turns off if you use the OTG port.
To fix this issue, you must remove(de-solder) the R94 from the C1+ PCB.
If you have the C1+ PCB Rev 0.4 2015/09/30, just remove a JUMPER on J8.
3. There is no backlight control except for the slide switch. So software can’t adjust the brightness neither turn on-off the backlight.

First booting will generate the boot.ini file automatically.
You can edit the boot.ini on your PC if you connect the SD/eMMC card after first booting(self-installation process). Change the vout mode to “HDMI”.

 

ODROID-VU7AP

Data sheet

Board Category
ODROID-C0
ODROID-C1+
ODROID-C2
ODROID-C4
ODROID-H2+
ODROID-HC
ODROID-N2+
ODROID-XU4

16 other products in the same category:

Product added to compare.