Your cart
There are no more items in your cart
ODROID
Active filters
- Board Category: ODROID Accessories
- Board Category: ODROID Cables
- Board Category: ODROID Connectors
- Board Category: ODROID Expansion Cards
- Board Category: ODROID Module Reader/Writer
- Board Category: ODROID Mounting kits
- Board Category: ODROID Power Supply
- Board Category: ODROID Switches & Battery
- Clear all
US$27.95
U3 IO Shield is the board that can be plugged on the neat of ODROID-U3 via tiny 8 pin IO connector. You can have 36 IO ports of GPIO/PWM/ADC. The shape and dimension are exactly same as ODROID-U3. It comes with 12pcs of PCB spacers for easier and solid stacking assembly.
US$6.95
Servo motor for custom project, use it with Odroid or any other hardware.
US$14.98
This board contains a USB3.0 to SATA3 controller (JMicron JMS578) allowing interfacing of a single 2.5" SATA HDD/SDD
US$5.27
Use this USB-DC Power Bridge board with ODROID-XU4 to connect ODROID-VU7 or VU7 Plus
US$59.95
The UPS2 for C1 is designed specifically for the ODROID-C1. Uninterrupted Power Supply is an electrical apparatus that provides emergency power to a load when the input power source, typically mains power, fails. The on-battery runtime of most uninterruptible power sources is relatively short but sufficient to start a standby power source or properly shut...
US$8.95
Blue illuminated Power Button with pre-assembled jumper wires.
US$59.95
Uninterrupted Power Supply is an electrical apparatus that provides emergency power to a load when the input power source, typically mains power, fails. The on-battery runtime of most uninterruptible power sources is relatively short but sufficient to start a standby power source or properly shut down the ODROID.
US$4.59
RTC backup battery Lithium primary battery to back up the RTC on XU board. This battery can keep the RTC running up to 5 years without external power supply.
US$8.00
Lithium Polymer rechargeable cell with a protection circuit.
US$15.60
Lithium Polymer rechargeable cell with a protection circuit.
US$8.75
Compact Stero Speaker for VU7A Plus and VU5A Plus
US$5.19
Ultrasonic ranging module HC - SR04 provides 2cm - 400cm non-contact measurement function.
US$3.00
The HC-SR501 Infrared PIR Motion Sensor Module auto-senses light in various applications (in house, basement, outdoor, warehouse, garage, etc,) for ventilator control, alarm, etc. Infrared technology (LHI778 probe design) high sensitivity & high reliability. ultra-low-voltage. widely used especially for battery-powered products. This HC-SR501 Infrared...
US$2.25
Note: Input voltage should be no more than rated voltage,or the module will be burnt
US$1.75
4 channel IIC I2C Logic Level Converter Bi-Directional Module 5V to 3.3V.
US$9.99
This RGB color sensor module is based on the TCS34725 sensor chip made by TAOS. The module is designed by Adafruit who Called it (the best color sensor in the market). This is much confirmed by our own testing and experiments in future Electronics Egypt lab.
US$3.80
Part for the I2S 2Watt Stereo Boom Bonnet Kit, for use with the ODROID-XU4 / XU4Q.
US$3.80
Part for the I2S 2Watt Stereo Boom Bonnet Kit, for use with the ODROID C1+ / C2.
US$8.95
This module is the 16 way GPIO expander for the I2C interface, and built with the MCP23017.MCP23017 has a high-speed I2C interface which supports the I2C frequency of 100KHz, 400KHz and 1.7MHz. The chip has 3 address pins, which can be set up for 8 different addresses. So 8 modules can be connected through two I2C buses to achieve up to 128 IO extensions.
US$14.95
System console interface board for platform development and debugging.
US$13.70
A single native (non-USB) SATA 3.0 port on the ODROID-M1 is provided for use with a 2.5inch HDD or SSD NAND Memory storage device. This SATA interface delivers near 500MB/s of sequential access. The SATA mount kit contains a SATA Data cable, a SATA Power cable, and a mount plate with some support screws. However, since the SATA power port doesn’t have a...